New Epx10000 Digital Frequency Synthesis Radar Remote Detector Gold Detector

New EPX10000 Digital Frequency Synthesis Radar Remote Detector
Control installation
Note: before the daily operation, the battery must be charged! If you do not charge, just will cause EPX10000 failure. If you show the same, this may be the first hint that the battery voltage is too low, you must charge. If the battery charge a whole night, the battery is still no electricity, you need to replace the battery or charger, or AC power output without electricity. If the battery is fully charged, the battery may need to be replaced. A new battery of batteries can work for EPX10000 about 8 hours.
Before opening the scanner, the transmitter is placed on the ground, and the sensor antenna is connected to the corresponding jack of the transmitter. When the transmitter is open. Absolutely do not plug the sensor, if so, it will cause damage to the machine.


Prior to using the EPX10000 scan, the first to do all necessary to connect the instrument.
1, the sensor is connected to the scanner testing (+) testing (-) on the hole, and the sensor probe into the soil
2, the signal is emitted by the transmitter antenna device in the corresponding interface.
3, with the power key to rotate the On/Off knob, turn on the power supply. At this time, in the liquid crystal display area, the power indicator light, the horizontal trimming, the longitudinal micro adjustment indicator light.
4, at this time, EPX10000 is scanning any of the selected elements. Before starting the program, please run 3-5 minutes, which will be followed by a simple explanation.
5, after the end of the operation, remember to turn off the EPX10000 power. In order to facilitate the use of the instrument, the battery needs to use a small charger connected to the power supply line charger.


Technical parameters:
1, check the depth range: 5-50m
2, check the distance range: 100-1000m
3, rechargeable battery: 8 hours of continuous work
4, voltage: 12VDC
5, temperature range: 450C a 850C
6, working humidity: 0~95% (non condensing)
7, 16 processor.40MIPS speed - 160MHz
8, 32 bit DDS synthesis chip. Output waveform
9, digital frequency synthesis X20PLL automatic frequency stabilizer, 0.1Hz
10, color LCD display, the resolution of 480x320 pixels
11, weight: 6.6KG gross weight: 10.5 KG
12, product size: 47X37X13.5cm








  New EPX10000 Digital Frequency Synthesis Radar Remote Detector
Control installation
Note: before the daily operation, the battery must be charged! If you do not charge, just will cause EPX10000 failure. If you show the same, this may be the first hint that the battery voltage is too low, you must charge. If the battery charge a whole night, the battery is still no electricity, you need to replace the battery or charger, or AC power output without electricity. If the battery is fully charged, the battery may need to be replaced. A new battery of batteries can work for EPX10000 about 8 hours.
Before opening the scanner, the transmitter is placed on the ground, and the sensor antenna is connected to the corresponding jack of the transmitter. When the transmitter is open. Absolutely do not plug the sensor, if so, it will cause damage to the machine.


Prior to using the EPX10000 scan, the first to do all necessary to connect the instrument.
1, the sensor is connected to the scanner testing (+) testing (-) on the hole, and the sensor probe into the soil
2, the signal is emitted by the transmitter antenna device in the corresponding interface.
3, with the power key to rotate the On/Off knob, turn on the power supply. At this time, in the liquid crystal display area, the power indicator light, the horizontal trimming, the longitudinal micro adjustment indicator light.
4, at this time, EPX10000 is scanning any of the selected elements. Before starting the program, please run 3-5 minutes, which will be followed by a simple explanation.
5, after the end of the operation, remember to turn off the EPX10000 power. In order to facilitate the use of the instrument, the battery needs to use a small charger connected to the power supply line charger.


Technical parameters:
1, check the depth range: 5-50m
2, check the distance range: 100-1000m
3, rechargeable battery: 8 hours of continuous work
4, voltage: 12VDC
5, temperature range: 450C a 850C
6, working humidity: 0~95% (non condensing)
7, 16 processor.40MIPS speed - 160MHz
8, 32 bit DDS synthesis chip. Output waveform
9, digital frequency synthesis X20PLL automatic frequency stabilizer, 0.1Hz
10, color LCD display, the resolution of 480x320 pixels
11, weight: 6.6KG gross weight: 10.5 KG
12, product size: 47X37X13.5cm








 

Press Brake

Steel Plate Bending Machine,CNC Press Brake with Tube-Bending Machinery,Steel Bending Machine,Hydraulic Press Brake Metal Brake Pad

NANTONG XINTONGWEI MACHINE TOOL CO．,LTD , https://www.inxtw.com