Application:

1, Brazing: it can be used for the brazing of various hardware cutting tools, diamond tools including diamond circular saw from diameter 300-2500mm, abrasive tool, drilling tool, alloy saw blade, hard alloy cutter, milling cutter, reamer, planning tool and solid center bit etc. It is suitable to used for the brazing of circular saw and other tools, usually 9 to 15 seconds is needed to braze one diamond blade.
2, Heat treatment: heat treatment of small parts
3, Melting: Melting below 2KG for gold, sliver, copper, brass, steel and iorn etc4,Forging,
5, Hardening
6, quenching
7,Annealing

Main characteristics:
1, MOSFET and Inverting technologies of First generation been used;
2, Simple structure and light weight;
3, Simple to operate, A few minutes is enough to learn it;
4, Simple to install, Installation can be done by unprofessional person very easily;
5, Advantages of the model with timer: The power and the operating time of the heating period and the retain period can be preset respectively, to realize a simple heating curve, this model is suggested to use for batch production to improve the repeatability;

Installing Desire
1, power supply wire: 6mm2 soft copper; Ground wire 4mm2 soft copper;
2, cooling water desire: Clean and not easy to scale, Inlet water temperature 25-36degree';
3, cooling water systerm: Running water; Circulating water from a pump to a tank; Use an industry refrigerate machine.

Some application exeample 


 

Application:

1, Brazing: it can be used for the brazing of various hardware cutting tools, diamond tools including diamond circular saw from diameter 300-2500mm, abrasive tool, drilling tool, alloy saw blade, hard alloy cutter, milling cutter, reamer, planning tool and solid center bit etc. It is suitable to used for the brazing of circular saw and other tools, usually 9 to 15 seconds is needed to braze one diamond blade.
2, Heat treatment: heat treatment of small parts
3, Melting: Melting below 2KG for gold, sliver, copper, brass, steel and iorn etc4,Forging,
5, Hardening
6, quenching
7,Annealing

Main characteristics:
1, MOSFET and Inverting technologies of First generation been used;
2, Simple structure and light weight;
3, Simple to operate, A few minutes is enough to learn it;
4, Simple to install, Installation can be done by unprofessional person very easily;
5, Advantages of the model with timer: The power and the operating time of the heating period and the retain period can be preset respectively, to realize a simple heating curve, this model is suggested to use for batch production to improve the repeatability;

Installing Desire
1, power supply wire: 6mm2 soft copper; Ground wire 4mm2 soft copper;
2, cooling water desire: Clean and not easy to scale, Inlet water temperature 25-36degree';
3, cooling water systerm: Running water; Circulating water from a pump to a tank; Use an industry refrigerate machine.

Some application exeample 


 

High Frequency Welding Tube Mill

Our High Frequency Welding Tube Mill is intended for manufacturing of round pipe of Φ16mm-Φ127mm with thickness of 0.5 mm–5.0 mm from cold-rolled and hot-rolled coil strip by means of unclosed tubular blank with its subsequent welding into tube, edge heating by means of solid state high-frequency welder, longitudinal seam welding in rolls of tube welding machine, cooling, further sizing or shaping and on-stream cutting of endless tube in measured lengths. 

Finished product can be of round, square or rectangular pipes.

a) High Frequency Welding Tube Mill Specifications:
Pipe diameter: Ø16–Ø127mm
Pipe Thickness: 0.5– 5.0mm
Pipe Length: 6-9m

Length Tolerance: 0-3mm

b) High Frequency Welding Tube Mill Steel Tape Specifications:
Material: Low Carbon steel (δb≤500Mpa, δs≤235Mpa)

Inner diameter:   Î¦580-Φ610mm

Outer diameter:   Î¦900-1500mm
Strip steel thickness: 0.5mm-5.0mm

The maximum weight: 5.0 tons

c) High Frequency Welding Tube Mill Electricity:
Dynamic power:  AC380V±10%, 3phases, 50Hz±10%
Control Power: AC220V±10%, one phase, 50Hz ±10%

Electric installed capacity: appro 450KW

e) High Frequency Welding Tube Mill Cooling water:
Reservoir for High Frequency equipment:15 m³, one set
Reservoir for circulating cooling water:15 m³, one set
f) High Frequency Welding Tube Mill Compressed air:
Pressure: 0.4Mpa
Flow: 0.5m3/h

g) High Frequency Welding Tube Mill speed: 

30-90m/min

Why choose to cooperate with us ?
1. We are professional manufacturer, so we can offer better price and after-sale service and shorter delivery time.
2. We have strong design & technical ability, we can design and manufacture as customer's requirement.
3. Our factory has been approved ISO 9001 certificate.
4. We have much experience for installation and training experience overseas.
5. We have successfully exported our machines to more than 90 countries, We all get good feedback.
6. We provide a free two years warranty for all our items.

7. OEM brand.

High Frequency Welding Tube Mill FAQ:
1.How to get a quotation of tube rolling line ?
Give me the diameters and thickness for the pipe .
Other spicific requirements is welcome, such as the speed,power and voltage you want.
2. Terms of payment ?

30% T/T, Balance to be paid before shipping after inspection.Also we accept the payment L/C, O/A , D/P.

3. What is your after-sale service ?

High Frequency Welding Tube Mill warranty period is 24  months, if the broken parts can't be repaired, we can send new to replace for free, but you need to pay the express cost yourself. we supply the technical support for the whole life of the equipment.

4. How to visit your factory ?

a.Fly to Beijing airport: By high speed train From Beijing Nan to Cangzhou Xi (1 hour), then we can pick up you.
b.Fly to Shanghai Airport: By high speed train From Shanghai Hongqiao to Cangzhou Xi(4.5 hours), then we can pick up you.

Steel Pipe Roll Forming Machine

Steel Pipe Roll Forming Machine,Carbon Steel Pipe Making Machine, High Frequency Welding Pipe Making Machine,Steel Pipe Making Machine

Zhongtuo Roll Forming Machinery Co., ltd , https://www.frameforming.nl