What are the problems that need to be paid attention to when installing p4LED display?
Many people do not know the specific reasons for the failure of the LED chip display module chip. This situation is not uncommon in the LED display products. The most common situation is that the driver chip or constant voltage driver chip of the entire LED display module will burn at the same time, or the individual row driver chip will be burned. So what are the reasons for this? Regarding the cause of this situation, ledp4 display manufacturer Yunhai Optoelectronics has obtained the following reasons:
First, the power supply of the display is reversed
For normal ledp4 display products, the power supply terminal position will have the VCC and GND marks, or the "+" and "-" marks, which represent the wiring positions of the positive and negative terminals, respectively. However, based on the lack of basic knowledge of electrical and electronic equipment, it is very likely that the positive and negative poles of the power supply will be reversed, even if the qualified technician has the possibility of operating errors. Reversing the positive and negative poles of the power supply will cause most of the constant voltage driving chips on the module to be seriously damaged or even burned.
Second, the module is abnormal and the line is always bright.
It is very common for the ledp4 display to show a line of dark lines and highlights. Most of them are caused by abnormal connection of the cable or error in debugging parameters. In general, a well-designed ledp4 display product will better avoid the protection circuit that is always bright and bright. After the line height is abnormally over-bright, if it is not eliminated in time, the row driver chip of the module will burn and destroy due to continuous high current operation and sharp rise in temperature. Of course, if compared with the previous cases, the current industry's ledp4 display module, the line driver chip's on-board power consumption will be relatively low, and the maximum operating current of most row driver chips will not exceed 4A. The possibility of the module driving the chip to smoke and burn out due to the constant brightness of the module is relatively small.
What are the problems that need to be paid attention to when installing p4LED display?
Third, the power supply voltage of the ledp4 module is too large
Usually the rated working voltage of the ledp4 display module is 4V-6V. The maximum limit working voltage of the integrated chip on the module will not be higher than 8V under normal conditions, and the maximum reverse voltage of the ledp4 lamp is below 8V. Therefore, the supply voltage of 8V or more will definitely damage the integrated chip and the ledp4 lamp. When the voltage reaches more than 8V, the conventional constant voltage driving chip will start to heat rapidly and is very likely to burn. Under normal circumstances, when the voltage exceeds 10-11V, it will continue to be energized for about 2 seconds, and the chip will burn to different degrees. Since the ledp4 display output voltage is 5V constant voltage switching power supply, the possibility of overvoltage is not great. Even if the control circuit of the switching power supply fails, the possibility that the output voltage is abnormal and reaches 9V or more is negligible. Therefore, in the process of actual application, the cause of the chip burning and burning is more or less positive or negative, followed by the module abnormality, and the voltage is too large.
For the outdoor led display, it is used outdoors. Therefore, it is inevitable to treat it differently from ordinary indoor LED display. LED electronic display installation requirements are also different from ordinary indoor LEDs. It must be done in detail on the installation. Otherwise it is very likely to cause trouble.
Outdoor LED display installation six requirements
1. Install lightning protection devices on the display and buildings.
The main body and the outer casing of the display are well grounded, the grounding resistance is less than 3 ohms, and the large current caused by lightning is discharged in time; the display may be attacked by strong electric current caused by lightning.
2. LED display itself waterproof measures
The screen body and the joint between the screen body and the building must be strictly waterproof and leakproof; the screen body should have good drainage measures, and the water can be discharged smoothly once the water accumulation occurs; pay attention to waterproof and moisture. The display screen is installed outdoors, often exposed to the sun and rain, and the working environment is bad. If the electronic equipment is wet or seriously damp, it may cause a short circuit or even a fire, causing malfunction or even fire, resulting in loss;
3. Circuit chip selection
Industrial-grade integrated circuit chips with an operating temperature between -40 ° C and 80 ° C are selected to prevent the display from starting due to low temperature in winter.
4. Install the ventilation equipment to cool down, so that the internal temperature of the screen is between -10 °C and 40 °C.
The axial fan is installed on the back of the screen body to discharge heat; when the LED display is working, it must generate a certain amount of heat. If the ambient temperature is too high and the heat dissipation is poor, the integrated circuit may not work properly or even be burned, thus making the display system impossible. normal work;
5. Must use ultra-high brightness LED
In order to ensure long-distance visibility under strong ambient light conditions, ultra-high-brightness LEDs must be used; contrast is increased. The audience is wide, the line of sight is far and the field of view is wide; the ambient light varies greatly, especially in direct sunlight.
6. Display medium selects new wide viewing angle tube
The viewing angle is wide, the color is pure, and the color is consistent. The outer packaging of the display medium with a life span of more than 100,000 hours is currently popular with a square cylinder with a cover, a silicone seal, and no metallization; its appearance is exquisite and beautiful, durable and has anti-sunlight. Direct, dustproof, waterproof, anti-high temperature, anti-circuit short circuit five features.
For fresh and healthy fruit- and vegetable juices
Perfect to squeeze fruits and vegetables
Modern design with stainless steel applications
Attach the included Shaker to the Juicer an mix delicious Cocktails.
Our products are currently selling to South American, Middle East, Africa and South East Asia. We are looking forward a long term and mutual-benefit cooperation with all the friends, and providing the first class OEM services. Our consistent principle: "Excellent quality, timely delivery, reasonable price, warmly service."
Hand Blender ,Mini Hand Blender,Cookworks Hand Blender,Small Hand Blender
FONY ELECTRICAL MANUFACTURING LTD , https://www.fonyblender.com