Many people do not know how to install the infrared alarm after purchasing the infrared alarm. Looking at the manual over and over again, it is always indispensable. The following describes the principle of infrared alarm and installation method, take a look at it.
First, the principle of infrared alarm
Infrared alarm is divided into active infrared alarm and passive infrared alarm. Here we take a look at the working principle of active infrared alarm and passive infrared alarm:
The active infrared intrusion alarm consists of a transmitter and a receiver. The transmitter consists of a power supply, a light source, and an optical system. The receiver is composed of an optical system, a photoelectric sensor, an amplifier, and a signal processor. The active infrared alarm is an infrared beam shield type alarm. The infrared light emitting diode in the transmitter emits a modulated infrared beam (the wavelength of this beam is between 0.8 and 0.95 microns) under the excitation of the power source. After the action of the optical system becomes parallel light emission. This beam is received by the receiver, the infrared photoelectric sensor in the receiver converts the optical signal into a signal, passes through the circuit and passes it to the alarm controller. The infrared rays emitted by the transmitter reach the receiver through the defense zone, forming a warning line. Under normal circumstances, the receiver receives a stable optical signal. When someone enters the cordon, the infrared beam is blocked and the infrared signal received by the receiver changes. This change is extracted, amplified, and properly processed. Alarm signal from the controller. At present, such alarms have two beams, three beams, and multiple beam infrared fences. Generally used in the perimeter to prevent more, the biggest advantage is to prevent the distance, can reach more than ten times the detection range of passive infrared.
Passive infrared alarm is mainly based on changes in the external infrared energy to determine whether someone is moving. The infrared energy of the human body is different from the environment. When people pass through the detection area, the position of this different infrared energy collected by the alarm changes, and then an alarm is issued through analysis. The human body has a constant body temperature, usually around 37 degrees, and it emits infrared light with a specific wavelength of about 10 [mu]m. A passive infrared alarm device works by detecting infrared radiation of about 10 [mu]m emitted by the human body. The 10 μm or so infrared emitted by the human body is enhanced by the Fresnel filter and collected on the infrared sensor. Infrared sensors usually use pyroelectric elements, which lose their charge balance when they receive a change in the temperature of infrared radiation from the human body, releasing charge outward, and the subsequent circuit can generate an alarm signal after detection and processing.
1. The passive infrared alarm is aimed at detecting human radiation, so the pyroelectric element must be very sensitive to infrared radiation with a wavelength of about 10 μm.
2. In order to be sensitive only to human body's infrared radiation, a special Fresnel filter is usually covered on its radiation surface, so that the environmental interference is obviously controlled.
3. The sensor includes two pyroelectric elements connected in series or in parallel with each other. In addition, the two polarization directions are exactly the opposite. The ambient background radiation has almost the same effect on the two pyroelectric elements, causing them to cancel each other's charge generation effects, so that the alarm has no signal output.
4. Once intrusion into the detection area, the human body infrared radiation is partially focused by the mirror and received by the pyroelectric element. However, the heat received by the two pyroelectric elements is different, and the pyroelectricity is different and cannot be cancelled. Call the police. Second, home infrared alarm installation
Before installing the infrared alarm, first the alarm host should be energized in a fixed position, and the alarm probe should be hung at a height of about 2 meters so that it can be tilted forward to obtain higher sensitivity. After the power is turned on, after a delay of about 1 minute, the alarm enters the alert state. At this time, if someone enters the monitoring area, an alarm will be given. Alarm about 1 minute, stop automatically. Then back to alert.
When the host enters, first press the power-off key on the remote control. When the infrared alarm sounds 'beep', the alarm is turned off and no alarm occurs when entering the warning zone. When the owner leaves the guard area, press the power button, and the alarm sounds with an audible alarm.
In case of an emergency, press the emergency alarm button and the infrared alarm is the emergency alarm.
There are high, medium and low sensitivity adjustments in the infrared alarm system. Users can adjust them according to their needs.
Mining Magnetic Separator Flotation Equipment
Mining Magnetic Separator & Flotation Equipment for EPC experiment lab testing machine processing equipment for sale
Mining Equipment Manufacturers Series Rcdd Conveyor Overband Magnetic Separator
Laboratory Magnetic Separator Mining Machinery Iron Ore Magnetic Roller Separator
Coltan Ore Processing Gold Mining Drum Separator High Intensity Wet Magnetic Separator
Metal Ore Mining Machine Magnetic Separator for Africa,East-south Asia countries
Gold Mining Equipment of Flotation Separation Machine with Factory Price
Complete Flotation Line Copper Mining Equipment EPC solution mining for Africa,Romania,Spanish,Chile,Mexico sale provider
Flotation Tank Copper Mining Equipment for Antimony
Mining Flotation Cell Equipment for Lead Zinc Ore Processing solution maker,EPC solution provider for Africa,Philippines
Flotation Machine can be used to separate nonferrous metal, ferrous metal, heavy metal, nonmetallic mine, chemical material such as gold, copper and recycling minerals. Each chute can inhale gas, sink magma, separate. No assisting equipment are required,and Flotation Machine must be levelly installed. Flotation Machine is easy to change the flow chart. The cycling way of magma is very reasonable. Flotation Machine can reduce the impurities to a great extent. There is automatic equipment on the magma surface, easy to adjust. The impeller also owns the upper and lower retroversion blade. The upper one makes the magma cycle upward, while the lower one makes the magma cycle downward.
Working principle of Flotation machine
The impellers are driven through V belt transmission, which brings centrifugal effect to form the negative pressure. On the one hand, the flotation machine inhales sufficient air to mix with ore slurry; on the other hand it stirs ore slurry and mix with medication to form the mineralized froth. To adjust the height of flashboard to control the liquid level and make the useful froth scraped by loam board. Each chute can inhale gas, sink magma, separate. No assisting equipments are required, and it must be levelly installed. It is easy to change the flow chart. The cycling way of magma is very reasonable. It can reduce the impurities to a great extent. There is automatic equipment on the magma surface, easy to adjust. The impeller also owns the upper and lower retroversion blade. The upper one makes the magma cycle upward, while the lower one makes the magma cycle downward.
Flotation Machine features:
1. Large inhaling capacity and low energy consumption;
2. Complete flotation circuit with inhaling air and pulp, no auxiliaries are needed;
3. Process is easy to be changed;
4. Reasonable circulation of pulp decreases coarse sand sedimentation;
5. Automatic controlling device makes adjustment more convenient.
Flotation Machine,Flotation Equipment,Froth Flotation Machine,Mining Magnetic Separator
Henan YK Prospecting Machinery Co., Ltd , https://www.yydthdrillingrig.com