Concrete mixer truck safety operation regulations

Concrete mixer truck operation and use procedures

1) Inspection must be performed before operation to ensure that the steering, braking, lighting, and signal systems are sensitive and effective. No cracks and serious damage are caused to the drums and chutes of the mixer truck. The blades are worn within the normal range, and the U between the chassis and the subframe is The bolts are well connected.

2) Understand construction requirements and site conditions. Select driving directions and parking locations.

3) Driving on social roads must obey the traffic rules. The turning radius should meet the requirements of the instruction manual, and the speed should not exceed 15 km/h. The speed of entering the station shall not exceed 5km.

4) It is forbidden to touch the rotating rollers and rollers by hand.

5) When reversing the unloading, it must obey the command, pay attention to the surrounding personnel, and immediately stop the vehicle if any abnormality is found.

6) It is forbidden to perform cleaning under the high voltage line.

Concrete mixer truck loading and maintenance procedures

1. During the running-in of new equipment, please do not load it at full capacity. It is recommended that 70%-80% of the loading capacity be loaded and the running-in period should be 3000km.

2. Before switching between positive and negative rotations, the operating handle must be returned to the neutral stop position, that is, the can body stops rotating and then changes direction, otherwise the reducer may be seriously damaged.

Third, in the high-speed or full-load climbing, the tank should stop turning to ensure traffic safety.

Fourth, all the connection screws should be regularly checked and fastened; all the lubrication points must be regularly filled with lubricating oil, regular inspections to replace the hydraulic oil, gear oil.

5. It is not advisable for the vehicle to load a slug with a slump of less than 12cm. Do not load a slug with a slump of less than 10cm.

6. Clean the inside and outside of the tank and keep the tank clean.

Seven, other maintenance details, please follow the "user's manual" implementation.


Waste Plastic Pyrolysis Plant

Pyrolysis Plant is used for recycling waste tire, waste plastic, waste rubber to fuel oil. According to the actual situation in every country and district, we developed different models of Batch Pyrolysis Plants for waste tires, rubber and plastic with daily capacity 5 -10 tons.

Batch Waste Tyre Pyrolysis Plant

Flowchat of Batch Waste Tyre Pyrolysis Plant

Batch Waste Tyre Pyrolysis Plant 

Advantages of Batch Waste Tyre Pyrolysis Plant

 

1. Full open door design: Speedy loading in and steel pulling out; Easily cooling down after one batch finished, saving time; No leaking with special high temperature flexible graphite packing.

2.  Unique Craft Condensers: High condensing efficiency with more oil output. Good quality oil, longer lifetime, and easy to clean.

3.  National Patent Unique Smoke Scrubbers: More efficient removal of the acid gas and dust of the smoke by neutralization, purification and absorption, environmental friendly without pollution.

4. National Patent Carbon Black Discharging System: Speedy fully enclosed Auto-discharging under high temperature, avoiding carbon black pollution, saving time.

5.  Automatic Submerged welding technology, ultrasonic nondestructive testing, both manual and the automatic safety devices.

6. Sync Gas Recycling System: Fully burned after recycling and utilization, saving fuel and preventing pollution.

7. Direct Heating System: Enlarging heating square to lengthen the lifespan of the reactor and easy to control the temperature.

8. National Patent, unique heat insulation shell; high efficiency temperature keeping, excellent energy-saving effect.

 

Technical Parameter of Batch Waste Tyre Pyrolysis Plant

NO.

ITEM

PROJECT

1

Equipment Model

XY-7

XY-8

2

Door Model

Full Open Door

Full Open Door

3

Suitable Raw Materials

Rubber/Plastic Products

Rubber/Plastic Products

4

Structure

Horizontal Type Revolves

Horizontal Type Revolves

5

Reactor Size

Φ2200*6000mm  Î¦2600*6600mm

Φ2200*6000mm  Î¦2600*6600mm

6

Capacity for One Batch

5-6Mt; 8-10Mt

5-6Mt; 8-10Mt

7

Oil Yield of Tires

40%-45%

40%-45%

8

Work Pressure

Normal Pressure

Normal Pressure

9

Reactor Rotation Speed

0.4R/M

0.4R/M

10

Fuels Choice

Coal, Wood

Coal, Wood, Gas, Oil

11

Power

18KW/H

18-25KW/H

12

Cooling Method

Water Cycling

Water Cycling

13

Type of Drive

External Annular Gear

External Annular Gear

14

Heating Method

Direct

Direct

15

Type of Installation

With Foundation

With Foundation/Integrated Base

16

Noise dB(A)

≦85

≦85

17

Operation Mode

Intermittent Operation

Intermittent Operation

18

Total Weight(MT)

25-40

25-40

19

Installation Space Required

30m*10m

30m*10m

20

Manpower

3~4/batch

3~4/batch

21

  Shipment

Ф2200×6000=1*40HC+1*40FR

Ф2600×6600=2*40HC+1*40FR

Ф2200×6000=1*40HC+1*40FR

Ф2600×6600=2*40HC+1*40FR

 

Waste Plastic Pyrolysis Plant

Waste Plastic Pyrolysis Plant,Plastic Pyrolysis Plant,Pyrolysis Of Plastic,Waste Plastic Pyrolysis Oil Plant

Shangqiu Jinpeng Industrial Co., Ltd. , https://www.recyclingthewaste.com

Posted on